| JIS B8605-2002 | 制冷用截止阀 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2002-1987 | 阀门结构长度标准E | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2205-1991 | 管法兰的计算标准 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS F7400-1996 | 造船.阀和旋塞.通用检验要求 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS E101 | 火力发电阀门 中文版标准下载 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2239-2004 | 铸铁管法兰.PDF | 现行 | 2025-07-08 | 2025-07-08 |
| JIS F7373-1996 | Shipbuilding-Cast iron 10K swing check valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2032-1995 | Wafer type rubber-seated butterfly valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2003-1994 | 阀门检验通则 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2071-2000 | 不锈钢阀门 (Steel valves) | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2007-1993 | 工业过程控制阀.检验和常规试验 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2011-2003 | 铜制闸阀、截止阀、角阀和止回阀 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2011-2004 | Bronze, gate, globe, angle, and check valves(Amendment 1) | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2011-2009 | Bronze, gate, globe, angle, and check valves(Amendment 2) | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2351-1990 | 25MPa 250kgf cm2 bite type of valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2001-1987 | 阀门公称通径及口径 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2004-1994 | General rules for marking on valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-1-2004 | Industrial-process control valves-PartControl valve terminology and general considerations | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-2-1-2005 | Industrial-process control valves-Part 2-1 Flow capacity-Sizing equations for fluid flow under installed conditions | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-2-3-2004 | Industrial-process control valves-Part 2-3 Flow capacity-Test procedures | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-2-4-2004 | Industrial-process control valves-Part 2 Flow capacity-Section 4 Inherent flow characteristics and rangeability | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-3-1-2005 | 工业过程控制阀 第3-1部分：尺寸.有法兰双通球形直型控制阀的端面间距尺寸和有法兰双通球形角型控制阀的中心与端面间距的尺寸 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-3-2-2005 | Industrial-process control valves-Part 3-2 Dimensions-Face-to-face dimensions for rotary control valves except butterfly valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-3-3-2005 | Industrial-process control valves-Part 3-3 Dimensions-End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-5-2004 | 工业过程控制阀 第5部分：标记 | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-6-1-2004 | Industrial-process control valves. Part 6 Mounting details for attachment of positioners to control valves SectionPositioner mounting on linear actuators | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-6-2-2005 | Industrial-process control valves-Part 6-2 Mounting details for attachment of positioners to control valves-Positioner mounting on rotary actuators | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-7-2004 | Industrial-process control valves-Part 7 Control valve data sheet | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2005-8-1-2004 | Industrial-process control valves-Part 8 Noise considerations-Section One Laboratory measurement of noise generated by aerodynamic flow through control valves | 现行 | 2025-07-08 | 2025-07-08 |
| JIS B2206-1995 | 铝合金管法兰的计算标准 | 现行 | 2025-07-08 | 2025-07-08 |